hoan.uk

Turnstile crossed-dipole antenna

Antennas

About

ToolIntermediateAges 14–9920 minITU-ARRL RF-TECH-08NGSS HS-PS4-2

Two crossed dipoles fed 90° apart make a circularly polarised antenna for NOAA and Meteor weather satellites. Set the frequency, drooping angle and matching, then read the cut list and inspect the 3D model.

Steps

0 of 4 done

How it works

RF impedance matching and the "U-balun" myth

1. Best: drooping elements (30° to 45°)

Angling the four arms downward like an inverted cone raises each dipole from 73 Ω to about 100 Ω. In parallel the feedpoint comes out near 50 Ω, so a 50 Ω coax connects directly with no transformer.

Z = 96 Ω / 2 = 48 Ω (SWR ≈ 1.04)

2. 75 Ω quarter-wave Q-section

If the elements stay horizontal (0° droop, feedpoint about 36 Ω), solder in a quarter-wavelength section of 75 Ω coax (RG-59 or RG-6) to bring the impedance towards 50 Ω.

L = 408.8 mm (RG-6 foam)

3. Direct 50 Ω coax feed (receive only)

For receive-only SDR dongles (RTL-SDR, HackRF): connecting 50 Ω coax straight to the 36 Ω feedpoint gives an SWR of about 1.38. The loss is under 0.12 dB, negligible in practice.

SWR = 50 / 36.5 ≈ 1.37:1

Important design and construction guidelines

  1. Shielded coax versus unshielded twin-lead. Every feedline and phasing line must be shielded 50 Ω coax (for example RG-58 or RG-316). Never use unshielded 300 Ω twin-lead ribbon: it detunes, picks up noise from nearby electronics and loses phase balance when wet or close to metal masts.
  2. Why a 30° to 45° droop is ideal for LEO satellites. With horizontal dipoles the radiation is focused at the zenith with deep nulls near the horizon (5° to 20° elevation). Angling the elements down by 30° to 45° spreads the lobe into a broad dome, so telemetry is received as soon as the satellite clears the horizon, and the feedpoint impedance rises towards 50 Ω.
  3. Switching polarization (RHCP and LHCP). The 90° delay line between Dipole 1 and Dipole 2 sets the sense of rotation. To change between RHCP (standard for NOAA and Meteor weather satellites) and LHCP you do not change any cable length: just swap the core and shield connections at the feedpoint of Dipole 2.
  4. Waterproofing and preventing coax corrosion. Water drawn by capillary action into the braid is the main cause of outdoor antenna failure: it oxidises the copper and turns the cable into an attenuator. Protect every solder joint with adhesive-lined heat-shrink and seal the feed box with neutral-cure RTV silicone (acetic-acid silicone corrodes copper).

Quiz

Why are the two dipoles fed 90° out of phase?
What does increasing the droop angle to 30° to 45° do?
How do you flip RHCP to LHCP without cutting any cable?
Element cut list and specifications
PartLengthNote
Dipole 1 arm (half)535.3 mmCut 2 arms. Mount along the X axis.
Dipole 2 arm (half)535.3 mmCut 2 arms. Mount along the Y axis.
Height above reflector564.7 mmSpacing between the dipoles and the reflector.

Crossed-dipole phasing harness

To radiate circular polarization (RHCP or LHCP) the two perpendicular dipoles must be fed exactly 90° out of phase. Join them with a quarter-wave (90°) coaxial delay line:

Coax typeVelocity factor (VF)Required delay line length
Solid PE (RG-58, RG-59)0.66359.8 mm
Foam PE (LMR-195, LMR-240)0.8436.1 mm
Teflon PTFE (RG-316, RG-142)0.7381.6 mm

Note: to switch between RHCP and LHCP in practice without cutting new cables, simply swap the core and shield solder leads on Dipole 2.

Bill of materials and construction checklist
ItemSpecification and notesQuantityLength
Radiating dipole arms (driven elements)Aluminium rod or copper tube Ø 4 mm4 pcs535.3 mm (+10 mm trim)
90° phase delay line (phasing coax)50 Ω coaxial cable (RG-58, RG-316, VF=0.66)1 pc359.8 mm
Reflector elements (ground screen)Aluminium rod Ø 4 mm (or mesh ≥ 1.1λ)2 pcs1,124.2 mm
75 Ω Q-match transformer section75 Ω TV coax (RG-6 foam VF≈0.75 or RG-59 solid VF=0.66)1 pc408.8 mm
Central support mastNon-conductive PVC pipe Ø 27 to Ø 34 mm1 pc≥ 965 mm
4-way cross fitting / hubPVC 4-way cross connector to hold the arms at 90°1 pcPVC
Fasteners and crimp ring terminalsStainless steel 304 bolts and nuts M4/M5 + ring terminals4 setsWeatherproof SS304
Weatherproofing and sealantIP65 junction box, neutral-cure RTV silicone, adhesive heat-shrink1 kit100% sealed for outdoor use