hoan.uk

Quadrifilar helix (QFH) antenna

Antennas

About

ToolAdvancedAges 18–9910 minITU-ARRL RF-TECH-06IB Physics:Wave-Phenomena

Two orthogonal, twisted loops of different sizes give a circularly polarised antenna with a wide, nearly hemispherical beam, ideal for weather and amateur satellites. Set the frequency, wire and twist and read the dimensions to cut.

Steps

0 of 5 done

How it works

Construction and drilling tips

Feedpoint and loop connections

At the top feedpoint, cross-wire the loops: terminal B of loop 1 connects to terminal C of loop 2, and terminal D of loop 1 connects to terminal A of loop 2. Connect the inner conductor of your coax cable to one pair and the shield to the other. Hide the mast in the 3D model to see this connection route clearly inside it.

Coaxial choke balun

Immediately below the bottom of the loops, wind your RG-58 coaxial feedline tightly around the PVC mast for 5 turns (the RF choke balun shown in the 3D model). It acts as a balun and stops common-mode currents on the coax shield.

Bending corners

When building QFH loops from rigid copper pipe, use a pipe bender that matches your bend radius of 6 mm. The 3D model draws these transition arcs accurately, which reduces mismatch compared with sharp corners.

Quiz

Why are the two loops of a QFH different in size?
What happens to the wire lengths if you raise the frequency from 436.5 MHz to 873 MHz?
Which change makes a QFH receive the opposite circular polarisation?

Drilling template

Print at 100% (actual size) and check that the red ruler measures 50 mm before you drill. Holes A to D are marked on three strips that wrap around the mast.

ON6JC/LW3HAZ QFH antenna design toolhttp://www.jcoppens.com/ant/qfhFrequency: 436.500 MHz | Support mast: 34.0 mm (circumference: 106.81 mm)Horizontal support: 6.0 mm | Polarization: RHCP | Twist: 0.5 turnSCALE CHECK (50 mm):50.0 mm(Set printer scale to 100% / actual size to match 50 mm)TopABCDCenterABCDBottomABCD106.38 mm212.76 mm

Wire forming template (unrolled)

RHCP (right hand / counter-clockwise)

Straighten the wire before bending. Mark all drilling and bending points with a pen or tape.

Mast IN/OUT is where the wire passes through the vertical support tube. T1/T2 are the feedpoint terminals. Helical twist direction, looking from the top: counter-clockwise (180° total rotation). Scroll horizontally to see the whole ruler.

Loop 1: larger (outer, red)Compensated total: 740.8 mmMast section: 34.7 mm
MASTFEEDFEEDT10.0 mmMast OUT17.4 mmStraight arm →44.1 mmTwist ↓ starts53.8 mmTwist ↓ ends316.6 mm→ Straight arm326.3 mmMast IN353.0 mmTube center370.4 mmMidpoint370.4 mmMast OUT387.8 mm→ Straight arm414.5 mmTwist ↑ starts424.2 mmTwist ↑ ends687.0 mmStraight arm →696.7 mmMast IN723.5 mmT2740.8 mm
Position (mm)DescriptionDistance from previous
0.0T1: feedpoint terminal 1 (inside the mast)—
17.4★ Mast OUT: exit from the vertical support tube (top of branch B1)+17.4
44.1Straight arm ends / corner bend starts (top of branch B1)+26.8
53.8Helical twist starts (branch B1, downwards)+9.6
316.6Helical twist ends (branch B1, downwards)+262.9
326.3Corner bend ends / straight arm starts (bottom of branch B1)+9.6
353.0★ Mast IN: entry into the vertical support tube (bottom of branch B1)+26.8
370.4↕ Vertical support tube center at the bottom+17.4
370.4◆ Wire midpoint: central point of the wire+0.0
387.8★ Mast OUT: exit from the vertical support tube (bottom of branch B2)+17.4
414.5Straight arm ends / corner bend starts (bottom of branch B2)+26.8
424.2Helical twist starts (branch B2, upwards)+9.6
687.0Helical twist ends (branch B2, upwards)+262.9
696.7Corner bend ends / straight arm starts (top of branch B2)+9.6
723.5★ Mast IN: entry into the vertical support tube (top of branch B2)+26.8
740.8T2: feedpoint terminal 2 (inside the mast)+17.4
Loop 2: smaller (inner, blue)Compensated total: 704.5 mmMast section: 34.8 mm
MASTFEEDFEEDT10.0 mmMast OUT17.4 mmStraight arm →41.7 mmTwist ↓ starts51.4 mmTwist ↓ ends300.9 mm→ Straight arm310.5 mmMast IN334.9 mmTube center352.3 mmMidpoint352.3 mmMast OUT369.6 mm→ Straight arm394.0 mmTwist ↑ starts403.6 mmTwist ↑ ends653.1 mmStraight arm →662.8 mmMast IN687.1 mmT2704.5 mm
Position (mm)DescriptionDistance from previous
0.0T1: feedpoint terminal 1 (inside the mast)—
17.4★ Mast OUT: exit from the vertical support tube (top of branch B1)+17.4
41.7Straight arm ends / corner bend starts (top of branch B1)+24.3
51.4Helical twist starts (branch B1, downwards)+9.6
300.9Helical twist ends (branch B1, downwards)+249.5
310.5Corner bend ends / straight arm starts (bottom of branch B1)+9.6
334.9★ Mast IN: entry into the vertical support tube (bottom of branch B1)+24.3
352.3↕ Vertical support tube center at the bottom+17.4
352.3◆ Wire midpoint: central point of the wire+0.0
369.6★ Mast OUT: exit from the vertical support tube (bottom of branch B2)+17.4
394.0Straight arm ends / corner bend starts (bottom of branch B2)+24.3
403.6Helical twist starts (branch B2, upwards)+9.6
653.1Helical twist ends (branch B2, upwards)+249.5
662.8Corner bend ends / straight arm starts (top of branch B2)+9.6
687.1★ Mast IN: entry into the vertical support tube (top of branch B2)+24.3
704.5T2: feedpoint terminal 2 (inside the mast)+17.4
Bill of materials and construction checklist (QFH BOM)
Item / componentSpecification and notesQuantityDimensions / length
Large helical loop (loop 1)Soft copper tube/wire Ø 4 mm (Bare aluminium wire or tube)1 loop740.8 mm
Small helical loop (loop 2)Soft copper tube/wire Ø 4 mm (Bare aluminium wire or tube)1 loop704.5 mm
Total copper conductor lengthTotal for both loops (includes +150 mm bending allowance)1 roll1.6 meters
Horizontal support crossbarsFiberglass/acrylic rod or copper tube Ø 6 mm4 pcsDc1: 98 mm | Dc2: 94 mm
Central support mastRigid PVC pipe Ø 34 mm1 pc≥ 574 mm
90° copper elbows (if soldered)Copper solder 90° elbows Ø 4 mm (skip if pipe-bent)8 pcsStandard copper
Feedline and RF choke balun50 Ω RG-58 coaxial cable (coiled 5 turns around the support mast)1 spoolBalun: ~534 mm + feedline
RF connector and weatherproofingChassis-mount female SMA/BNC, PVC endcap, RTV silicone sealant1 set100% outdoor sealed